Channels | 4CH+Ext |
Bandwidth | DCvn_100MHz (-3dB) |
Rise time | 3.5ns |
Bandwidth Limit | 20MHz |
Vertical Sensitivity | |
Resolution | 8 bit |
:1mV*vn_10V/div | |
Input Coupling | AC, DC, GND |
Input Impedance | 1MΩ// 16pF approx. |
DC Gain Accuracy | ±(3% X |Readout| + 0.1div + 1mV)when 2mV/div or greater is selected ±(5% X |Readout| + 0.1div + 1mV)when 1mV/div is selected; |
Polarity | Normal & Invert |
Maximum Input Voltage | 300Vrms, CAT I (300Vrms CAT II with GTP-151R/251R/351R/501R 10:1 probe ) |
Offset Position Range | 1mV/div vn_ 20mV/div : ±0.5V |
50mV/div vn_ 200mV/div : ±5V | |
500mV/div vn_ 2V/div : ±25V | |
5Vvn_10V/div : ±250V | |
Waveform Signal Process | +, -, ×, ÷, FFT, FFTrms ,d/dt ,∫dt ,√ ,Integration*, Differentiation* *: App installation required” |
Trigger | |
Source | CH1 ,CH2, CH3*, CH4* |
Line, EXT, D0-D15** | |
Holdoff range | 10nsvn_10s |
Coupling | AC,DC,LF rej. ,HF rej. ,Noise rej. |
Sensitivity | DC vn_ 100MHz Approx. 1div or 1.0mV |
| 100MHz vn_ 200MHz Approx. 1.5div or 15mV |
| 200MHz vn_ 300MHz Approx. 2div or 20mV |
External Trigger | |
Range | ±15V |
Sensitivity | DC vn_ 100MHz Approx. 100mV |
100MHz vn_ 200MHz Approx. 150mV | |
200MHz vn_ 300MHz Approx. 150mV | |
Input Impedance | 1MΩ±3%vn_16pF |
Horizontal | |
Time base Range | 1ns/div vn_ 100s/div (1-2-5 increments) |
ROLL: 100ms/div vn_ 100s/div | |
Pre-trigger | 10 div maximum |
Post-trigger | 1000 div maximum. |
Time base Accuracy | ±20 ppm over any ≥ 1 ms time interval |
Real Time Sample Rate | Max.:2GSa/s |
ET Sample Rate | 100GSa/s maximum for all models |
Record Length | Max:2Mpts |
Acquisition Mode | Normal, Average, Peak Detect, Single |
Peak Detection | 2ns (typical) |
Average | selectable from 2 to 256 |
X-Y Mode | |
X-Axis Input | Channel 1; Channel 3* |
*four channel models only | |
Y-Axis Input | Channel 2; Channel 4* |
| *four channel models only |
Phase Shift | ±3° at 100kHz |
Display | |
TFT LCD Type | 8" TFT LCD SVGA color display |
Display Resolution | 800 horizontal × 600 vertical pixels (SVGA) |
Interface | |
RS232C | DB-9 male connector X1 |
USB Port | USB 2.0 High-speed host port X2, USB High-speed 2.0 device port X1 |
Ethernet(LAN) Port | RJ-45 connector, 10/100Mbps with HP Auto-MDIX (option) |
Go-NoGo BNC | 5V Max/10mA |
Logic Analyzer (Option) | |
Sample Rate | 500MSa/s |
Bandwidth | 200MHz |
Record Length | 2M max |
Input Channels | 16 Digital (D15 - D0) or 8 Digital (D7vn_D0) |
Trigger type | Edge, Pattern, Pulse Width, Serial bus (I2C, SPI, UART),parallel |
Thresholds | Quad-D0vn_D3, D4vn_D7 ,D8vn_D11* ,D12vn_D15* (*:DS2-16LA only) |
Threshold selections | TTL, CMOS, ECL, PECL, User Defined |
Threshold accuracy | ±100mV |
User-defined Threshold Range | ±10V |
Maximum Input Voltage | ±40 V |